Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L

$208.85 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location: Ontario, California, United States
Ships to: US,
Item: 404824060833

eBay Symptoms of Power Steering Rack Failure You turn the steering wheel to go down the street, and the wheel is extremely stiff. You open the hood and look for an obvious problem. The power steering belt is still there, and the power steering is full. The power steering fluid is black as night, but it is full. The belt looks a little worn, and it’s past the four-year power steering belt replacement interval. So you put a new one on. A few days later it happens again. This is what’s known in the trade as “morning sickness.” It doesn’t get better, only worse. quality_autoparts Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L Symptoms of Power Steering Rack Failure You turn the steering wheel to go down the street, and the wheel is extremely stiff. You open the hood and look for an obvious problem. The power steering belt is still there, and the power steering is full. The power steering fluid is black as night, but it is full. The belt looks a little worn, and it’s past the four-year power steering belt replacement interval. So you put a new one on. A few days later it happens again. This is what’s known in the trade as “morning sickness.” It doesn’t get better, only worse. The cause is normal wear and tear on the internal parts of the power steering rack, or “the rack” as we call it. The black power steering fluid is black because of metal worn from the inside of the rack and had become like sandpaper, eating away at the rack. So you will need to replace the power steering rack and flush the power steering system to get rid of all the old fluid. Can I Replace the Power Steering Rack Myself? Replacing a power steering rack can be an easy job on some vehicles, rear wheel drive vehicles for example, or it can be most difficult and nasty in others. So how do you know if yours is an easy or hard one? Reading the removal procedure in a service manual will tell you what’s involved, and you can decide if it is within your skill level. Be advised, however, that the manual may not be entirely accurate in that it will tell you to do something you may not have to do. For instance, on one Oldsmobile the book says you have to support the engine and lower the sub-frame by, at least, three inches. Well maybe you do, and maybe you don’t. You can most often twist and turn and jiggle it out through the wheel well opening without too much difficulty. But read the procedure first. It will give you torque specifications, what, if any, nuts and bolts need to be replaced and if there are any “O” rings that you need to replace. Before taking anything apart. Look at the new rack. Take note of mounting bolt holes and the high pressure and return line fittings. Then jack up the X and support it with jack stands. Never go under a vehicle supported only by a jack. Take a look at where the mounting bolts are, where the steering column coupling is and the power steering lines. After looking at what the job entails, you may decide it is beyond your skills and have a shop do the job. What You Will Need ？ Jack Jack stands Wrenches Ratchet and socket set with extensions Screwdrivers Pliers or vise grips Hammer Wire brush Tie rod separator or ball joint fork Engine support fixture (If required) Power steering filter Power steering fluid Automatic transmission fluid New power steering rack Latex gloves (Optional) Note: Before You Start Follow these instructions Xefully. Read and be sure you understand them before you begin. Gather together all of your tools and supplies before you begin. Allow plenty of time to do the job so you don’t have to hurry. Remember that these are general instructions. For more detailed instructions about your specific vehicle, consult an appropriate repair manual. Beware of hot objects, sharp instruments, and hazardous materials. Don’t substitute tools unless you’re sure you won’t compromise either your safety or the performance of your vehicle. Never work on a vehicle that is only supported by a jack. Put the X on jack stands to support it while you work. Work on a solid, level surface. Never jack a X up on dirt or grass. Check for any fluid leaks or cracked power steering lines. Replace them as necessary. How to Replace a Power Steering Rack? Feel you’re up to it? Are you ready to get started? Then let’s do it! Put the wheels in a straight-ahead position. The steering wheel should be in the center position. Remove the key from the ignition and make sure the steering wheel is locked. You do not want the steering wheel to turn while removing the rack. Doing so will make it possible for the spiral cable in the steering wheel to unwind and become useless. Crack loose all the wheel lug nuts Raise and support the vehicle with approved jack stands. Remove both front wheels. Remove the Steering Shaft Coupler Outer Seal and unbolt the upper pinch bolt on the Steering Shaft Coupler assembly. Detach the outer tie rod ends. You may need to use a special tie rod end puller to get them off. You can rent one at the local rental store. Most times a sharp rap with a BFH on the end of the tie rod mount will shock it loose. Do not hit the tie rod end itself. Remove any parts required to gain access to the rack mounting bolts, lines and steering coupling. Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines. Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines. It may be easier to get a wrench to swing on a power steering line fitting once you’ve unbolted the rack and moved it a bit. Also, reattaching the lines may be easier before the new rack is bolted in place. Place a drain pan under the vehicle and remove the hydraulic power steering pressure hose and power steering return hose from the power steering rack. Now comes the fun part, twist and turn and jiggle it out through one of the wheel well openings. Make sure the kids are in the house because certain words will be necessary to coax the rack out and they are not words little ears should hear. If the new rack has new tie rod ends, measure the overall length of the old rack and tie rod assembly. Set the overall length of the new assembly to this same dimension by twisting the tie rod ends on their threads. Keep the rack centered and split the overlap difference between the left and right rod ends as you do this, or the steering wheel will be off-center when you’re done. If you are reusing the old tie rod ends, crack the lock nuts loose. Count how many full turns it takes to remove the tie rod ends. Center the new rack and install tie rod ends the same number of turns on the new rack. Again, check the overall length and split the difference. Install the new rack using the same words you used to get it out. Reconnect the power steering lines, using new “O” rings, if required. Usually, the high-pressure line uses a slightly larger “O” ring so be Xeful not to mix them up. Reconnect the Steering Shaft Coupler assembly and bolt the rack back into place. Reattach the tie rod ends to the steering knuckles. Use new cotter pins for the castellated nuts; never reuse the old cotter pins. Put the wheels back on and torque the lug nuts to specifications. Remove the return line from the power steering pump and place the end into a bucket. Fill the power steering pump and start the engine until clean fluid comes out of the return hose. You may be able to install an inline filter in the return line to protect the new rack. I have known guys who have used fuel filters for this purpose. Have the front end aligned to reset the toe-in adjustment to specification or the vehicle will handle poorly and wear out the tire quickly. Bleeding The Power Steering System The final step is bleeding the trapped air out of the system. Fill the reservoir, start and idle the engine. Turn the steering wheel back and forth stop to stop. Just touch the stop, do not hold it there, or you may damage the power steering pump. Do this 10 to 15 times. Power steering fluid that is a tan color or has a beer head contains air. Turn the engine off and let it sit 15 minutes or longer. Top off the power steering fluid and start the engine again. Repeat until the fluid looks normal. And that’s it. Figure on the job taking the better part of a day, depending on the type of installation. you would set aside a weekend just in case you run into problems. Feature: High-quality replacement :Power steering rack and pinion This part may also be known as : Power steering (PAS) or steering assist system 100% tested For reliability and performance. Not rebuilt or remanufactured Top performance For long service life Undergone strict tests to ensure reliable performance Air Tested to Ensure Reliable Performance Hydraulically Tested to Ensure Internal By-Pass for Both High and Low Pressures Road simulated for proper functioning simple installation and and long life as a guarantee Backed by satisfying after-sales service 3 year warranty Interchange Part Number: 22-1014 Rack 2009 ES3675 ES3676 4KS1700130 Fits: BUICK RAINIER 2004-2007 All Models YES CHEVROLET TRAILBLAZER 2002 All 16mm tie rod Models YES CHEVROLET TRAILBLAZER EXT 2002 All 16mm tie rod Models YES CHEVROLET TRAILBLAZER 2003-2009 All Models YES CHEVROLET TRAILBLAZER EXT 2003-2006 All Models YES CHEVROLET SSR 2003-2006 All Models YES GMC ENVOY 2002 All 16mm tie rod Models YES GMC ENVOY 2003-2009 All Models YES ISUZU ASCENDER 2002 All 16mm tie rod Models YES ISUZU ASCENDER 2003-2008 All Models YES OLDSMOBILE BRAVADA 2002 All 16mm tie rod Models YES OLDSMOBILE BRAVADA 2003-2006 All Models YES Item Specifics Brand quality_autoparts Manufacturer Part Number Q10882801LA Part Type Rack & Pinion Complete Unit,Steering Rack,Steering Gear Performance Part Yes Installation method Performance/Custom Fitment Type Performance/Custom Material High Quality Steel Surface Finish Polished, Rust Protected Manufacturer Warranty 3 Years Vintage Car Part Yes Fitment Type Direct Replacement Rack Type Hydraulic Greasable or Sealed YES Other Part Number Steering gear Rack Material corrosion and rust prevention Note Backed by satisfying after-sales service Advantage Rotate quickly and normal position Interchange Part Number 22-1014,Rack 2009,26101416 Superseded Part Number 19320512,1030206,8192077800 OE/OEM Part Number rack replacement kit,rack and pinion,power rack parts OE Number Power Steering Rack,Steering Rack and Pinion Sub Type Rack and Pinion Assembly, Rack and Pinion Rack Gear Package Dust plug Universal Fitment No Itment Note Top performance For long service life Mounting Hardware Included As the picture Fits OLDSMOBILE BRAVADA 2003-2006 All Models YES For OLDSMOBILE BRAVADA 2003-2006 All Models YES Payment Immediate payment is required during checkout. We will process and ship orders once checkout is completed. Shipping We offer international shipping through eBay global shipping program.We reserve the right to change shipping carrier and shipping method for efficient and on-time deliveries. Our store is not responsible for carrier delays such as weather or natural disasters. Returns All returns must be approved with a Return Material Authorization Number (RMA #) that must be included with the return To receive an RMA Please contact Our Customer Service. All returned products will be inspected. Returns processing may take up to 3 business days from the time your product is received at our return facility locations. Contact Us Often, Customers reach out to us to help confirm fitment of parts prior to purchase. We always recommend cross referencing a part number to ensure fitment as well.You may Contact Us by locating the “Contact Seller” Button within a listing. Feedback We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them! quality_autoparts DESCRIPTION PAYMENT SHIPPING RETURN POLICY CONTACT US Shop Category Store Home Alternator sensor Catalytic Converter Transmission Oil Filter Other Hot Item Alternator fits 2010-2013 Hyundai Sonata 11-13 Kia Optima 2.4L 37300-2G150 11491 USD 104.57 Windshield Washer Level Sensor For Toyota Camry Corolla RAV4 Sequoia Avalon USD 14.99 Alternator for 2011-2014 Dodge Avenger,2011-2016 Journey Grand Caravan 3.6L USD 86.27 Alternator 125A for Nissan Murano SE Sport Utility 3.5L 2003-2006 2007 AHI0027 USD 75.92 11553 Alternator for 2013 2014 2015 2016 Dodge Dart L4 2.0L 2.4L 140A 12V USD 115.12 Excellent Delivery Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us New List Item 110A 12V CW 6-Groove Alternator for 2003-2004 Nissan Pathfinder INFINITI G35 USD 103.13 Throttle Position Sensor TPS For 1995 1996-2007 Dodge Ram 1500 3.9L 5017479AA USD 13.20 Exhaust Manifold W/Catalytic Converter For 2003-2007 Murano 3.5L V6 Y-pipe USD 92.74 150A 12V Alternator 11352 for 2008-2022 Toyota Sequoia 2007-2021 Tundra 5.7L USD 112.17 Manifold Absolute Pressure MAP Sensor for Ford Focus Ranger Escape Mazda 3 6 MKZ USD 14.81 Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L Symptoms of Power Steering Rack Failure You turn the steering wheel to go down the street, and the wheel is extremely stiff. You open the hood and look for an obvious problem. The power steering belt is still there, and the power steering is full. The power steering fluid is black as night, but it is full. The belt looks a little worn, and it’s past the four-year power steering belt replacement interval. So you put a new one on. A few days later it happens again. This is what’s known in the trade as “morning sickness.” It doesn’t get better, only worse. The cause is normal wear and tear on the internal parts of the power steering rack, or “the rack” as we call it. The black power steering fluid is black because of metal worn from the inside of the rack and had become like sandpaper, eating away at the rack. So you will need to replace the power steering rack and flush the power steering system to get rid of all the old fluid. Can I Replace the Power Steering Rack Myself? Replacing a power steering rack can be an easy job on some vehicles, rear wheel drive vehicles for example, or it can be most difficult and nasty in others. So how do you know if yours is an easy or hard one? Reading the removal procedure in a service manual will tell you what’s involved, and you can decide if it is within your skill level. Be advised, however, that the manual may not be entirely accurate in that it will tell you to do something you may not have to do. For instance, on one Oldsmobile the book says you have to support the engine and lower the sub-frame by, at least, three inches. Well maybe you do, and maybe you don’t. You can most often twist and turn and jiggle it out through the wheel well opening without too much difficulty. But read the procedure first. It will give you torque specifications, what, if any, nuts and bolts need to be replaced and if there are any “O” rings that you need to replace. Before taking anything apart. Look at the new rack. Take note of mounting bolt holes and the high pressure and return line fittings. Then jack up the X and support it with jack stands. Never go under a vehicle supported only by a jack. Take a look at where the mounting bolts are, where the steering column coupling is and the power steering lines. After looking at what the job entails, you may decide it is beyond your skills and have a shop do the job. What You Will Need ？ Jack Jack stands Wrenches Ratchet and socket set with extensions Screwdrivers Pliers or vise grips Hammer Wire brush Tie rod separator or ball joint fork Engine support fixture (If required) Power steering filter Power steering fluid Automatic transmission fluid New power steering rack Latex gloves (Optional) Note: Before You Start Follow these instructions Xefully. Read and be sure you understand them before you begin. Gather together all of your tools and supplies before you begin. Allow plenty of time to do the job so you don’t have to hurry. Remember that these are general instructions. For more detailed instructions about your specific vehicle, consult an appropriate repair manual. Beware of hot objects, sharp instruments, and hazardous materials. Don’t substitute tools unless you’re sure you won’t compromise either your safety or the performance of your vehicle. Never work on a vehicle that is only supported by a jack. Put the X on jack stands to support it while you work. Work on a solid, level surface. Never jack a X up on dirt or grass. Check for any fluid leaks or cracked power steering lines. Replace them as necessary. How to Replace a Power Steering Rack? Feel you’re up to it? Are you ready to get started? Then let’s do it! Put the wheels in a straight-ahead position. The steering wheel should be in the center position. Remove the key from the ignition and make sure the steering wheel is locked. You do not want the steering wheel to turn while removing the rack. Doing so will make it possible for the spiral cable in the steering wheel to unwind and become useless. Crack loose all the wheel lug nuts Raise and support the vehicle with approved jack stands. Remove both front wheels. Remove the Steering Shaft Coupler Outer Seal and unbolt the upper pinch bolt on the Steering Shaft Coupler assembly. Detach the outer tie rod ends. You may need to use a special tie rod end puller to get them off. You can rent one at the local rental store. Most times a sharp rap with a BFH on the end of the tie rod mount will shock it loose. Do not hit the tie rod end itself. Remove any parts required to gain access to the rack mounting bolts, lines and steering coupling. Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines. Depending on accessibility, at this point, you can remove the power steering rack mounting bolts, or crack the power steering high pressure and return lines. It may be easier to get a wrench to swing on a power steering line fitting once you’ve unbolted the rack and moved it a bit. Also, reattaching the lines may be easier before the new rack is bolted in place. Place a drain pan under the vehicle and remove the hydraulic power steering pressure hose and power steering return hose from the power steering rack. Now comes the fun part, twist and turn and jiggle it out through one of the wheel well openings. Make sure the kids are in the house because certain words will be necessary to coax the rack out and they are not words little ears should hear. If the new rack has new tie rod ends, measure the overall length of the old rack and tie rod assembly. Set the overall length of the new assembly to this same dimension by twisting the tie rod ends on their threads. Keep the rack centered and split the overlap difference between the left and right rod ends as you do this, or the steering wheel will be off-center when you’re done. If you are reusing the old tie rod ends, crack the lock nuts loose. Count how many full turns it takes to remove the tie rod ends. Center the new rack and install tie rod ends the same number of turns on the new rack. Again, check the overall length and split the difference. Install the new rack using the same words you used to get it out. Reconnect the power steering lines, using new “O” rings, if required. Usually, the high-pressure line uses a slightly larger “O” ring so be Xeful not to mix them up. Reconnect the Steering Shaft Coupler assembly and bolt the rack back into place. Reattach the tie rod ends to the steering knuckles. Use new cotter pins for the castellated nuts; never reuse the old cotter pins. Put the wheels back on and torque the lug nuts to specifications. Remove the return line from the power steering pump and place the end into a bucket. Fill the power steering pump and start the engine until clean fluid comes out of the return hose. You may be able to install an inline filter in the return line to protect the new rack. I have known guys who have used fuel filters for this purpose. Have the front end aligned to reset the toe-in adjustment to specification or the vehicle will handle poorly and wear out the tire quickly. Bleeding The Power Steering System The final step is bleeding the trapped air out of the system. Fill the reservoir, start and idle the engine. Turn the steering wheel back and forth stop to stop. Just touch the stop, do not hold it there, or you may damage the power steering pump. Do this 10 to 15 times. Power steering fluid that is a tan color or has a beer head contains air. Turn the engine off and let it sit 15 minutes or longer. Top off the power steering fluid and start the engine again. Repeat until the fluid looks normal. And that’s it. Figure on the job taking the better part of a day, depending on the type of installation. you would set aside a weekend just in case you run into problems. Feature: High-quality replacement :Power steering rack and pinion This part may also be known as : Power steering (PAS) or steering assist system 100% tested For reliability and performance. Not rebuilt or remanufactured Top performance For long service life Undergone strict tests to ensure reliable performance Air Tested to Ensure Reliable Performance Hydraulically Tested to Ensure Internal By-Pass for Both High and Low Pressures Road simulated for proper functioning simple installation and and long life as a guarantee Backed by satisfying after-sales service 3 year warranty Interchange Part Number: 22-1014 Rack 2009 ES3675 ES3676 4KS1700130 Fits: BUICK RAINIER 2004-2007 All Models YES CHEVROLET TRAILBLAZER 2002 All 16mm tie rod Models YES CHEVROLET TRAILBLAZER EXT 2002 All 16mm tie rod Models YES CHEVROLET TRAILBLAZER 2003-2009 All Models YES CHEVROLET TRAILBLAZER EXT 2003-2006 All Models YES CHEVROLET SSR 2003-2006 All Models YES GMC ENVOY 2002 All 16mm tie rod Models YES GMC ENVOY 2003-2009 All Models YES ISUZU ASCENDER 2002 All 16mm tie rod Models YES ISUZU ASCENDER 2003-2008 All Models YES OLDSMOBILE BRAVADA 2002 All 16mm tie rod Models YES OLDSMOBILE BRAVADA 2003-2006 All Models YES Item Specifics Brand : quality_autoparts Manufacturer Part Number : Q10882801LA Part Type : Rack & Pinion Complete Unit,Steering Rack,Steering Gear Performance Part : Yes Installation method : Performance/Custom Fitment Type : Performance/Custom Material : High Quality Steel Surface Finish : Polished, Rust Protected Manufacturer Warranty : 3 Years Vintage Car Part : Yes Fitment Type : Direct Replacement Rack Type : Hydraulic Greasable or Sealed : YES Other Part Number : Steering gear Rack Material : corrosion and rust prevention Note : Backed by satisfying after-sales service Advantage : Rotate quickly and normal position Interchange Part Number : 22-1014,Rack 2009,26101416 Superseded Part Number : 19320512,1030206,8192077800 OE/OEM Part Number : rack replacement kit,rack and pinion,power rack parts OE Number : Power Steering Rack,Steering Rack and Pinion Sub Type : Rack and Pinion Assembly, Rack and Pinion Rack Gear Package : Dust plug Universal Fitment : No Itment Note : Top performance For long service life Mounting Hardware Included : As the picture Fits : OLDSMOBILE BRAVADA 2003-2006 All Models YES For : OLDSMOBILE BRAVADA 2003-2006 All Models YES PaymentShippingReturnsContact UsFeedback Immediate payment is required during checkout. We will process and ship orders once checkout is completed. We offer international shipping through eBay global shipping program.We reserve the right to change shipping carrier and shipping method for efficient and on-time deliveries. Our store is not responsible for carrier delays such as weather or natural disasters. All returns must be approved with a Return Material Authorization Number (RMA #) that must be included with the return To receive an RMA Please contact Our Customer Service. All returned products will be inspected. Returns processing may take up to 3 business days from the time your product is received at our return facility locations. Often, Customers reach out to us to help confirm fitment of parts prior to purchase. We always recommend cross referencing a part number to ensure fitment as well.You may Contact Us by locating the “Contact Seller” Button within a listing. We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them! All rights reserved.

Frequently Asked Questions About Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L in My Website

xdvrdrones.com is the best online shopping platform where you can buy Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L from renowned brand(s). xdvrdrones.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Steering Rack For 2003-2009 Chevrolet Trailblazer LT Sport Utility 4-Door 4.2L on xdvrdrones.com?